Yamaha Tio1608-D

Baseret på 4 anmeldelser

Vi matcher udlandets lave priser - og giver dansk kundeservice

10.599,- (Inkl. moms)
Fri fragt (op til 20 kg.)
Prismatch i
Forudbestilling til uge 43

Vi anbefaler sammen med

100% dansk netbutik

Varenr.: YAM-TIO1608D

  • Plug and Play
  • Dante-equipped I/O rack
  • 16 microphone/line inputs and 8 line outputs

Beskrivelse

Yamaha Tio1608-D

 

The Tio1608-D is a Dante-equipped I/O rack with 16 microphone/line inputs and 8 line outputs. The Tio together with the TF series delivers an extraordinarily natural and musical sound. In combination with the TF series consoles, the Tio  can be connected with up to three devices with a quick and easy setup.


Yamaha The NY64-D sound card is required to make the two products talk together.

Specifikationer

EAN: 4957812593458
Type Mixer

General specifications

Sampling frequency rate External 44.1kHz or 48kHz
Signal delay Less than 3ms INPUT to OUTPUT, connect with TF5 and NY64-D using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz
Total harmonic distortion Less than 0.1% +4dBu@20Hz-20kHz into 600Ω, Gain=+66dB / Less than 0.05% +4dBU@20Hz-20kHz into 600Ω, Gain=-6dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18dB/octave filter @80kHz
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT, Fs=44.1kHz or 48kHz
Dynamic range 108 dB, INPUT to OUTPUT, Gain=-6dB / 112 dB, DA Converter
Hum & noise level Equivalent input noise -128dBu, Gain=+66dB *Measured with A-weighting filter
Residual output noise -88dBu, ST master off *Measured with A-weighting filter
Crosstalk -100dB, adjacent INPUT/OUTPUT channels, Input Gain = -6dB *Measured with a -30dB/octave filter @22kHz
Heat dissipation 100-240V, 50/60Hz, 43.5kcal/h
Power requirements 100-240V, 50/60Hz
Power consumption 50W
Dimensions W 480mm (18-7/8")
H 88mm (3-4/8")
D 364mm (14-3/8")
Net weight 5.7kg (12.6lbs)
Accessories Owner’s Manual, Power Cord(2.5m), Rubber stoppers(4)
Others Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Analog input characteristics

Input Terminals GAIN Actual Load
Impedance
For Use With
Nominal
Input Level Connector Balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5kΩ 50-600Ω Mics &
600Ω Lines
-82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)
Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)

In these specifications, 0dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch. 
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND

Analog output characteristics

Output Terminals Actual Source
Impedance
For Use With
Nominal
Output Level Connector Balanced /
Unbalanced
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type*1 Balanced

In these specifications, 0dBu = 0.775Vrms.
*1.1: GND,2: HOT, 3: COLD

Digital Input & Output Characteristics

Terminal Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 16ch ( Tio1608-D to other devises)
8ch (Other devises to Tio1608-D)
etherCON Cat5e